Home > Event Id > Event Id 1058 Gpt.ini Access Is Denied

Event Id 1058 Gpt.ini Access Is Denied

Contents

In other words, your hosts file should look like this (if you have just two domain controllers): 121.121.121.121 yourdomainname.com 121.121.121.122 yourdomainname.com Where 121.121.121.121 = the ip address of the local domain Every time I tried to copy (with domain admin privileges) files from a DC to a member server, it would give me an ďaccount disabledĒ message. I could view \\dcname\anyothershare but not \\dcname\sysvol. Solution Executed command: dfsutil /PurgeMupCache DFSUtil Command Reference:¬†http://technet.microsoft.com/en-us/library/cc782897(WS.10).aspx see also¬†http://support.microsoft.com/kb/314494 Like this:Like Loading... Check This Out

See ME250842 and ME887303, which have information about "troubleshooting group policy application problems". VMWare or VPN virtual adapters). As for DFS, I believe that article that James posted for you should help, and maybe the main issue going on here. The contents of the gpt.ini dummy file were: [General] Version=0.

What Is Gpt.ini File

x 1 Alexandr A. x 1 Anonymous Check file and printer sharing on the primary NIC. x 1 Anonymous I had been having this problem for about a month on both my DCs.

x 2 EventID.Net This problem occurs when network address translation (NAT) prevents LDAP requests from reaching services on the domain server. Verify you can read gpt.ini using the full network path obtained in the previous step. Do I need to run that Dfsutil on the XP client? Event Id 1058 Error Code 65 Going in the DNS zone config for the zone (WINS tab), only the DC that was down was listed under the "Use WINS forward lookup" option.

An example of English, please! Windows Cannot Access The File Gpt.ini For Gpo Bob Blork 22 May 2014 10:24 AM nice job Page 1 of 1 (5 items) © 2015 Microsoft Corporation. All of this information appears in the event. Changing the settings for VSE and then changing some of your GPO settings just like Mark Minasi said, will solve it.

Delete the temporary Group Policy. Event Id 1058 Group Policy and for quite a while now (unsure how long - I suspect a year or more) they have been having challenges enumerating & applying group policies.  Event ID 1030/1058 would appear Any services that have been disabled (NetBios Helper, DHCP Client >> service, any at all). > Will check >> 8. Alternates as to which DC it afflicts.

Windows Cannot Access The File Gpt.ini For Gpo

The server has two NICs, one of which is disabled. Posted by DWHunter on 06/18/2011 at 01:41 AM in Active Directory, Networking, Server 2008 | Permalink Digg This | Save to del.icio.us | | Comments You can follow this conversation by What Is Gpt.ini File The name of the domain controller is logged in the details of the error event. Event Id 1058 On Domain Controller I will assume from your original post with the error message that "louverttbw1.co.uk" is you domain name.

When you configure the domain controller in this way, the Workstation service on the domain controller cannot connect to the domain controller's Sysvol share. http://computerhelpdev.com/event-id/description-event-id-1058-source-userenv.php Configured for routing and > Remote Access, > DHCP and DNS. Go to Network Connections -> Advanced Settings. Only DNS > 5. Windows Cannot Access The File Gpt.ini For Gpo 1058

Netbios broadcasts are done on a local lan. Thanks for clearing that up! > > Kind regards > Paul > > Glenn L, Oct 19, 2004 #9 the yeti Guest <----Snip> I am having the same problem here. You can configure WINS. http://computerhelpdev.com/event-id/1058-event-id-windows-7.php Paul Paul D, Oct 15, 2004 #5 Ace Fekay [MVP] Guest In news:ckoije$m8u$2surf.net, Paul D <> made a post then I commented below > Thanks, Ace > That is a

Try it -- it works. Event Id 1030 Group Policy Failed The second octet MUST be "168", so you can use 192.168.0.x if you like, but I recommend that you use 192.168.16.x to avoid any possible conflicts with VPN connections which are x 2 Paul Cocker The event was occurring in combination with EventID 1030 from source Userenv and was referencing a GPO that existed on the PDC but not on the other

stako_ex is using a routable IP subnet.

After successfully configuring my new card, the problem appeared. This worked for me (and > EVERYONE else who has tried this), and NOTHING has worked > for over 6 months until this. See ME830676 for more details. Dfsutil /purgemupcache In the network adapter settings I had to activate the "Client for Microsoft Networks".

and the problem was fixed. The workstations will all have to be rebooted to get new DHCP assignments (or you can just disable/enable the NIC on each one). To see these settings on a domain controller go to Start -> Run, and enter MMC. http://computerhelpdev.com/event-id/event-id-1058-group-policy-gpt-ini.php x 70 Bryan Lockwood In my case, the problem (on Windows XP Pro, SP2) traced back to a broken DFS client.

GPOs are populated in the SYSVOL record and distributed out to clients and servers using Netbios broadcasts. I changed security settings for the share but it didn't have any effect... 0 LVL 74 Overall: Level 74 SBS 64 Windows Server 2003 30 Message Expert Comment by:Jeffrey Kane Home Best Practices Manuals Good Stuff Home > Active Directory, Group Policy, Server 2003 > Event ID: 1058 and 1030 (Group Policy AccessDenied) Event ID: 1058 and 1030 (Group Policy AccessDenied) Yes, you need a hosts file on EACH domain controller.

x 1 Peter Hayden Event ID 1030/1058 on a domain controller may indicate that the Group Policy "Digitally sign communications ..." has been set too high. It > works fine on > the 2k3 server its self. x 1 Klaus Charlier The events 1030 and 1058 occurred on Windows XP clients trying to logon to a Windows 2000 single PDC. So, what else could I do to fix this error??? 0 Message Author Comment by:stako_ex ID: 219718452008-07-10 Oh, about the 192.0.0.xxx subnet...

This step had been missed in renaming the domain. There could be issues with static IP's assigned to other servers or devices, but that shouldn't take more than a few minutes to change as well. Once I changed my password to adhere to the requirements, the errors stopped and I could edit group policy objects once again. The following steps solved it: 1.

Any services that have been disabled (NetBios Helper, DHCP Client > service, any at all). When I manually added NS records for the current DNS servers the 1030 & 1058 errors stopped some 6 hours later. Is DFS running? Are any of these services disabled: MS Client, F&P Services, NetBIOS?

Group Policy processing aborted. Leave a Reply Cancel reply Enter your comment here... One of two DCs logged 1030 and 1058 errors.